表示若操作錯誤，將發生危險，可能導致中等程度的人身傷害以及財產損失，或嚴重損害的事項。
Due to mishandling, a dangerous condition might occur and there is possibility of medium human disorder or material disorder.
There might be cases where there are heavy damages.

警告 ?Warning

1.
請勿在易爆性環境、易燃性氣體環境和受水濺射的場所使用。否則可能導致火災、受傷及觸電。
Do not use in an explosive atmosphere, flammable atmosphere and locations where water falls onto. It might cause a fire, injury or electric shock.
2.
應由具備專業知識的人員進行安裝、接線、檢查等作業,否則可能導致觸電或受傷。
Installation, wiring connection, inspection, etc. should be done by a person with professional knowledge.
You might get an electric shock or be injured.
3.
通電狀態下請勿進行移動、接線及檢查等作業，否則可能導致觸電或受傷。
Do not move, wire or inspect the motor when applying current. You might get an electric shock or be injured.
4.
通電狀態下請勿拉扯、夾住導線。否則可能導致觸電。
Do not pull out or push in the lead wire when applying current. You might get an electric shock.
5.
通電狀態下請勿觸摸連接端子的導電部。否則將導致觸電。
Do not touch the connection terminals, etc. when applying current. You will get an electric shock.
6.
停電時請務必切斷電源。否則恢復供電時機器若突然啟動，會導致人員受傷。
Shut off the power supply of your product when an electric power failure occurred. The motor and your product may start running suddenly when the electric power is back and you might get injured.

注意 ?Precautions

1.
用于對社會及公共場所可能產生較大影響的設備時，請設置電機停止時設備的保護措施。
If the motor is used in a equipment that has large social and public effects, please prepare equipment protection measures in case the motor stops.
2.
運行過程中請勿觸摸旋轉部位及驅動部位。否則可能導致受傷。
Do not touch the rotating or moving parts during operation. You might get injured.
3.
靜電可能導致電機及設備發生故障，安裝時請采取適當的防靜電措施。
Static electricity causes motor and equipment failures. Take appropriate measures against static electricity during installation of motor.
4.
請勿手持導線，否則可能導致通電不良或因掉落導致人員受傷。
Do not hold the lead wire part because it might cause an electric current disorder or injury due to falling motor.
5.
請勿將不匹配的電機安裝至設備，否則可能導致人員受傷、設備損壞、甚至引發火災。
Make sure you receive the right motor at receipt. Installation of wrong motors to your product might cause a fire, injury or electric shock.
6.
連接電機與設備時，請注意找正、皮帶張力、鏈條張力、滑輪的平行度等。直接連接時請注意連接精度。使用皮帶或鏈條時，請正確調整張力。運行前請切實緊固滑輪和聯軸器的緊固螺栓。否則可能因碎片飛濺而導致受傷或設備損壞。
Pay attention to following things when you assemble the motor to your product, centering, belt tension, chain tension, parallelism of pulley and etc. In case of a direct coupling, make sure its accuracy is kept. If in use of the belt or chain, make sure its correct tension is kept. Make sure the bolt to fix the pulley, coupling is tightened before running. It might cause an injury and breakage of your product brought by airborne fragment.
7.
連接設備與電機前請確認旋轉方向，否則可能導致受傷或設備損壞。
Make sure the direction of motor rotation is correct. Wrong rotation might cause a fire and a breakage of your product, moreover, you might get injured.
8.
發生異常時請立即停止設備的運行。否則可能導致觸電、受傷、或引發火災。
Shut down the operation of your product and motor when extraordinally happenings occurred. It might cause a fire, injury or electric shock.
9.
請勿將電機放置于可能受到雨水和水滴濺射或存在腐蝕性氣體和液體的場所中保存。否則可能導致漏電及故障。
Do not expose motors to rain, water drop, corrosive gas and liquid. It might cause an electric leakage and breakage.

其他要求 ?Other precautions

1.
請勿拆分電機，否則將改變電機特性。
Do not disassemble motor to avoid motor performance change.
2.
移動電機時，請握住電機主體，避免向導線引出部施力。
Hold motor body, not lead wire exit to avoid external force to lead wire exit.
3.
插拔連接器時，請握住連接器外殼，避免向導線施力。
Hold connector housing when plugging or unplugging connector not to apply external force to connector pin.
4.
將齒輪等壓入輸出軸時，請注意勿向軸承、軸等施加過大的力。
Be careful not to apply abnormal force to bearing, shaft, etc. when putting pulley, gear, etc. on to motor shaft.
5.
請勿使用可能掉落過或受過強大外力的電機。
Do not use any motors that were accidentally dropped.
6.
壽命、噪音和振動的測評必須以安裝在設備上的方式進行。
Prior to usage of our motor, assemble it to your product and verify its life, noise and vibration which are to be determined by the type and operation condition of your product.
7.
請勿在產生有害氣體的環境下使用。否則可能加速樹脂部位的老化。
Do not use motor in environment generating noxious gas that affects motor performance.
8.
請在規格規定的存放溫度和濕度范圍內存放，并防止結露。
Ensure that motor are stored at the temperature and humidity range defined in the specification and at no dew condition.
9.
若無其他規定，安裝好的電機其線圈溫度必須控制在130℃以下。
Ensure that motor coil does not exceed 130℃ when mounted on your product unless otherwise specified.
10.
在高溫下使用時，應采取安全措施，包括避免人體接觸，粘貼警示標簽等。
In case of usage at high temperature, take safety measures, such as designing not to expose motor to touch human body or sticking a warning label.
11.
為防止因電機及電路故障而導致人身傷害或引發火災，請安裝溫度保險絲并配備保護電路。
Provide fuse, protection circuit, etc. to assure safety against injuries to human body or fires that may arise from accidental failure of motor or circuit.
12.
請勿將磁卡、手表等靠近電機。否則可能導致電機失效。
Do not bring a magnetic card, a watch etc. close. They may stop function.
13.
請勿將本產品用于與原子能、飛機或軍事相關的設備。
Do not use our motor for any applications related to military, aircraft or nuclear energy.
14.
本公司的產品不是針對醫療設備設計制造的。
請用作即使使用本公司電機發生意外故障，也不會導致可能危及生命的設計內容。
萬一發生危及生命的情況，本公司不承擔任何責任。
Our motors are not designed and manufactured for any applications relating to medical equipment.
Please use our motors in a design which would not lead to any problem on human life even if an accidental failure occurred in the motors.
15.
因用戶自行改造電機而導致的故障不屬于本公司的保修范圍，本公司對此概不負責。
We do not take any responsibility of converted motors.
16.
請勿從電機上去除銘牌。
Do not remove the name plate on the motor.
17.
請避免使用與電機上的連接器相同的連接器。否則可能導致接線有誤。
Do not use the same connector as motor side for the connection to your product because it might cause a faulty interconnection.
18.
若要將電機挪用到其他裝置或機型上，請預先告知本公司。
In case you apply the same motor to an other product, please let us know in advance.